BLACK FRIDAY SALE · UP TO 35% OFFENDS IN

(231)383-8936

Jeep YJ Shock Tower Bundle

Front and rear Jeep YJ shock towers in one order, built for 2.5″ coilovers or ORI struts. Choose the bump mount add-ons you need. Then add the link subframe bracket or rear sway bar mount if your build calls for them.

Join ORA Insider free and earn points on this item.

Description

Get front and rear Jeep YJ shock towers in one order, built for 2.5″ coilovers or ORI struts. Pick your tower options, then add the subframe bracket or rear sway bar mount if your build needs them.

The front towers handle anything from a coilover swap to a full 1-ton axle swap. The rear towers take on a full 1-ton 4-link swap. So you get the whole frame side of the job, bundled together for your convenience.

What’s in the Jeep YJ Shock Towers Bundle

You get a pair of front towers and a pair of rear towers. Here’s what each pair brings to the build.

  • YJ Front Shock Tower. The tower straddles the factory frame rail, so it fits easily and adds strength. It sits roughly centered on the frame for good shock clearance and angle. Plus, it still clears the factory steering shaft. You get left and right uprights and tops, 4 inner shock tabs and 4 tear drop capture washers.
  • YJ Rear Shock Tower. Each tower frenches 1-1/4″ into the frame. That fits up to a 2.5″ coilover or ORI at proper shock angles. It also clears 40s flexed out. The towers use 3/16″ steel in a bent design, and you only notch half the frame. You get left and right uprights and tops, plus 4 inner shock tabs.

Both towers key only one of the two shock tabs into the tower. That means you set the spacing you need: 1.25″, 1.5″, or 1.6″ for ORIs. On the front towers, the tabs also use our captured weld washers for extra strength. Plus, every part ships unwelded.

Pick Your Tower Options

Each tower pair comes in two versions. So you only buy the mounts your setup needs.

  • Front towers. Go with the towers alone, or add the panhard and bump can mount. That add-on brings left and right bump can frame mounts for 2″ bump cans. It also adds a driver side frame panhard mount with a 2″ inside mounting width.
  • Rear towers. Go with the towers alone, or add the bump mount. That add-on brings left and right bump can saddle mounts. It also adds a frame french gusset plate for each side.

Optional Add-Ons

  • YJ Link Suspension Subframe Bracket. It mounts the lower links on a Jeep YJ 4 link or 3 link build. The outer plate indexes off the middle body mount, close to the center of the wheelbase. Plus, the drop-down design leaves a smooth bottom and sets you up for a flat belly skid. It’s laser cut from 3/16″ steel in a 2″ or 2.625″ inside mounting width.
  • YJ Rear Sway Bar Mount. We designed it around the universal Antirock 45″ sway bar kit with 17″ arms. The bar packages between the frame and body, in front of the rear axle. So it works with the rear towers, which hold the shocks behind the axle. The plates slide over the kit’s 1.75″ tube and capture it a full 360°.

So add either one only if your build calls for it.

Built for a Jeep YJ Coilover Conversion

In other words, these towers are the frame side of a Jeep YJ coilover conversion. Because the rear shocks mount behind the axle, you keep room over the axle for a frenched-in bump stop. That also leaves space for a sway bar in front of the axle.

So your Jeep YJ shocks run at proper angles front and rear. Plus, every part is Made in the USA, in our own shop.

Installing Your Jeep YJ Shock Towers

Plan on welding and fabrication for this kit. So only tackle the welding yourself if you’re an experienced welder.

  • Front towers. Weld the shock tabs to the top plate first. Then weld the top plate to the upright, which makes finish welding much easier. We also recommend a cross brace between the two front towers for added strength.
  • Rear towers. We designed them around a 1″ body lift. The lift helps, but you don’t need it. Without the lift, mount the tower 1″ lower, or cut the inner fender instead.
  • Fitment. Expect some grinding and fitting during install.

Also, you’ll supply your own bump cans, shocks and Antirock sway bar kit. The towers carry an oversize shipping charge and can’t ship to a PO box. Offroad Anonymous is not liable for improper installation.

Finishing out the axle side? These Jeep YJ shock towers pair well with our Lower Link Bracket with Shock Mount up front. For the rear, check out our Offset Axle Shock Mount – Pair.

You may also like…

  • Offset Shock Mount

    Offset Axle Shock Mount – Pair

    $53.00
    Add to cart
  • Universal Triangulated 4 Link Bracket Kit (Option 1)

    Universal Triangulated 4 Link Bracket Kit – 2.625″ Mount Width

    Configure bundle
  • Lower Link bracket with shock mount

    Lower Link Bracket with Shock Mount

    Price range: $55.00 through $60.00
    Select options This product has multiple variants. The options may be chosen on the product page
  • Lower Link Bracket

    Lower Link Bracket

    Price range: $35.00 through $42.00
    Select options This product has multiple variants. The options may be chosen on the product page

Join Today -
Get 10% Off Your First Order

Join the ORA list and get 10% off your first order as a new customer.

Our newsletter is a great way to stay up to date with new products, build content, and future sales.